Specifications: Item Name: Whoop and toothpick 2-IN-1 FPV Racer Drone;
Wheelbase: 65mm;
Size: 80mm80mm30mm;
Weight: 17.5g (without battery).
Features: The lightest 1S Whoop and Toothpick 2-IN-1 fpv drone.
Comes with tooth pick frame for convert.
Powerful and efficiency.
The lightest 1s AIO 5IN1 F4 flight controller.
Unibell SE0702 brushless motors with pcb wire board.
Built-in OPENVTX up to 400mw.
Low profile Canopy design.
Motor: Mode: SE0702 KV23000;
Configu-ration: 9N12P;
Stator Diamter: 7mm;
Stator Length: 2mm;
Shaft Diameter: 1mm;
Motor Dimension(Dia.Len): 9.5mm14mm;
Weight(g): 1.5g;
Cells(Lipo): 1S only.
Propeller: Weight: 0.19g;
Material: PC;
Pitch: 1 inch;
Props Dia: 30mm;
Center Hole Dia: 1mm.
Flight controller: (ELRS SPI RX version)DiamondF4 ELRS FC Firmware target: CrazybeeF4SX1280;
(Frsky SPI RX version) DiamondF4 FR FC Firmware target: CrazybeeF4FR;
MCU: STM32F411CEU6 (100MHZ, 512K FLASH);
Sensor: MPU-6000 or ICM20689 or BMI270(SPI connection);
Original whoop size compatible;
Power supply: 1S battery input (DC 2.9V-4.35V);
Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready;
Built-in Betaflight OSD(SPI Control);
Built-in 5.8G OPEN VTX;
Built-in SPI ELRS V2.0/Frsky receiver;
Built-in 5V 1A BEC.
Onboard 4in1 ESC: MCU upgraded to EFM8BB21;
Power supply: 1S LiPo/LiPo HV;
Current: 5A continuous peak 6A (3 seconds);
Support BLHeliSuite programmable;
Factory firmware: O_H_50_REV16_;
Default protocol: DSHOT600.
Onboard SPI ExpressLRS 2.4GHz Receiver: Packet Rate option: 50Hz/150Hz/250Hz/500Hz;
ExpressLRS Firmware version: V2.0;
RF Frequency: 2.4GHz;
Antenna : Enameled copper wire antenna;
Telemetry output Power: <12dBm;
Receiver protocol: SPI ExpressLRS;
Compatible with ExpressLRS V2.0 TX Module;
Couldnt flash separately ExpressLRS firmware.
Onboard Frsky SPI D8 receiver Version: SPI BUS receiver Frsky D8 compatible;
Compatible Non EU transmitter D8 model;
Channels: 8ch;
Failsafe support;
No ground interference ( Transmitter and receiver 1 m from the ground): 200m~300m.
Onboard 5.8g OPENVTX: Firmware version: OPENVTX;
Smartaudio v2.1;
PIT Mode support;
RCE Mode support;
Channels: 48ch;
Transmitting Power: 0/RCE/25mw/100mw/400mw;
Power supply: DC 5V;
Current (5v): <650ma (400mw).
Runcam Nano3: Model: RunCam Nano 3;
Image Sensor: 1/3 CMOS;
Horizontal Resolution: 800TVL;
Lens: 2.3mm(M6.5) FOV 140 ;
Signal System: NTSC;
S/N Ratio: >50dB;
Electronic Shutter Speed: Auto;
Auto Gain Control (AGC): Auto;
Min. Illumination: 0.01Lux1.2F;
D-WDR: Auto;
Day/Night: Color;
Power: DC 3-5.5V;
Current: 110mA5V 120mA3.3V;
Housing Material: ABS;
Net Weight: 1.2g;
Dimensions: L14mmW14mmH9mm.
Lipo Battery: Capacity: 300mAh;
Voltage: 3.8v;
Continuous Discharge Rate: 30C;
Size: 57mmx12mmx7mm;
Weight: 7.5g;
Connector: PH2.0.
Package Included: 1x 65mm whoop Frame (Mobula6 frame);
1x 65mm toothpick frame(Mobeetle6 frame);
Option1: DiamondF4 ELRS built-in SPI ELRS receiver;
Option2: DiamondF4 FR built-in SPI FRSKY receiver;
4x SE0702 KV23000 Unibell brushless motor;
1x Gemfan 1210 31mm propeller(4cw+4ccw);
1x Runcam Nano3;
1x Built-in 5.8G 48ch 25mw-400mw OPENVTX;
2x 1s 300mah Lipo battery;
1x Mobula6 canopy;
1x Propeller disassemble tool;
1x Screwdriver.
Product Attributes:
